Do you own an air compressor? Have you ever had water get into the lines and cause a lot of problems? If so, it’s important to know how to prevent this from happening in the future.
There are many different ways that can be done, but here are three major ways:
1) Use a filter or drying agent on your hose before connecting it to your compressor
This is a good solution to keep water out of your compressor. It’s important because if you don’t, the moisture will end up getting into your airline and causing problems later on down the road.
A filter or drying agent like anti-freeze can be used on any length of hose but it’s best for long hoses when they’re in storage so that water has enough time to evaporate before being put into use again by homenewtools
2) Keep the air compressor outside when possible
This is a good solution because it will keep the air compressor dry and less likely to get wet. If you’re using an outdoor compressor, this can be done fairly easily as long as there isn’t any rain or snow coming down on top of it.
It’s best for indoor compressors that are in basements or storage sheds because if they were left outside all day then moisture could come inside and cause problems later on too.
The third way to prevent water from getting into your airlines is by keeping them higher up than anything else nearby like grass, dirt, mud, etc.
This would also help prevent children from playing near it and touching everything which can lead to contamination issues of other sorts. The last thing you want when trying to keep water out of compressor lines is to have a hose leak or something and then you get the opposite effect.
If it’s not possible for your air compressor to be raised off the ground, there are some other options available. For outdoor compressors, make sure that they’re elevated at least 18 inches (45 cm) from any surface such as grass, dirt, etc.
On an indoor one try putting it on cement blocks which will also help keep rodents away too.
The last option would be with garage equipment stands made specifically for air compressors but these can quickly become expensive so only do this if necessary.
3) Install drain plugs at both ends of your hoses
A common mistake is to forget to install drain plugs at the ends of a hose. This ensures that if there’s water in your compressor line, it won’t leak out and get into other areas where you don’t want it to go.
It also keeps dirt from getting inside the lines which will clog them down quickly.
You can buy these types of fittings for next to nothing so this isn’t an expensive fix but one worth doing right away before any problems arise.
How do I keep moisture out of my air compressor?
There are a few ways to do this. The first would be with an air compressor pump guard which is inserted between the tank and the hoses.
This ensures that water doesn’t get in, but it does have its disadvantages as well since you’ll need to install one on each end of your hose line so they’re not too expensive and can quickly become cumbersome.
The second option for keeping moisture out of your compressor’s lines: use spray-on lubricant such as WD40 or even cooking oil like vegetable oil throughout any parts where there might be contact from touching metal or other materials (since these are both non-conductive).
Moisture won’t stick to surfaces coated in this way and will just slide off instead without creating rust spots or other damage.
This is a good option for anyone who doesn’t have an air compressor pump guard or one available that can be installed, but it does require more effort and time from the person doing so in order to do a thorough job with these coating substances.
In each of these two options, there are pros and cons that need to be evaluated by the individual before they decide which one will work best for their specific use-case scenario.
For any particular instance, it may not even matter because different people run into varying levels of moisture issues at various times during operation while trying to keep water out of air compressor lines. It’s always better to take steps beforehand if possible though!
conclusion
The best option for anyone who doesn’t have an air compressor pump guard or one available that can be installed, but it does require more effort and time from the person doing so in order to do a thorough job with these coating substances.
In each of these two options, there are pros and cons that need to be evaluated by the individual before they decide which one will work best for their specific use-case scenario.
For any particular instance, it may not even matter because different people run into varying levels of moisture issues at various times during operation while trying to keep water out of air compressor lines.
